Dell Latitiude E6500 Скачать руководство пользователя страница 19

Страница: 19 / 72

Back to Contents Page

Display

Dell™ Latitude™ E6500 Service Manual

Removing the Display Assembly

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the
Regulatory Compliance Homepage at: www.dell.com/regulatory_compliance.

Follow the instructions in

Before Working on Your Computer

Close the display and turn the computer over.

Remove the bottom of the base assembly (see

Removing the Bottom of the Base Assembly

Remove the hinge covers (see

Removing the Hinge Covers

Disconnect the display cable, the WPAN cable, and the modem cable.

Unroute the display cable and the wireless cables (WLAN, WWAN, and WPAN).

Remove the M2.5 x 5-mm screws from each hinge.

Removing the Display Assembly

Replacing the Display Assembly

Removing the Display Bezel

Replacing the Display Bezel

Removing the Display Panel

Replacing the Display Panel

Removing the Display Panel Brackets

Replacing the Display Panel Brackets

Display Inverter

Removing the Camera and Microphone Assembly

Replacing the Camera and Microphone Assembly

Removing the Latch Hook Assembly

Replacing the Latch Hook Assembly

Removing the Display Cover

Replacing the Display Cover

NOTE:

Some graphics may vary slightly, depending on whether you ordered a cold-cathode fluorescent lamp (CCFL) display or an LED display.

CAUTION:

After unrouting the cables, place all cables to the rear and away from the computer.

1 display cable 2 WPAN cable

3 WLAN cable

4 WWAN cable

1 M2.5 x 5-mm screws (2)

Содержание Latitiude E6500









































































Результаты поиска

Содержание Latitiude E6500

Отзывы:

Похожие инструкции для Latitiude E6500

Бренды по названию

Популярные бренды

Dell Latitiude E6500, Руководство по обслуживанию

Результаты поиска

Содержание Latitiude E6500

Отзывы:

Похожие инструкции для Latitiude E6500

Бренды по названию

Популярные бренды