Dell Latitiude E6500 Скачать руководство пользователя страница 33

Страница: 33 / 72

Replacing the Hard Drive

If you are replacing the hard drive with a new one, remove the new drive from its packaging.

Save the original packaging for storing or shipping the hard drive being replaced.

Attach the bezel to the hard drive using the M3 x 3mm screw.

Slide the hard drive into the bay until it is fully seated.

If removed, replace the bottom of the base assembly (see

Replacing the Bottom of the Base Assembly

Replace and tighten the four M3 x 3-mm hard-drive screws.

Replace the battery.

Turn the computer over so the top side is up, open the display, and start your computer.

If you have installed a new drive, try and boot it. If it doesn't boot:

Use your operating system installation media to install the operating system for your computer (for more information, see your

Setup and Quick

Reference Guide

Use the

Drivers and Utilities

media to install the drivers and utilities for your computer (see your

Setup and Quick Reference Guide

for information).

Back to Contents Page

hard drive bezel

M3 x 3mm screw

hard drive

CAUTION:

Use firm and even pressure to slide the drive into place. If you use excessive force, you may damage the connector.

Содержание Latitiude E6500









































































Результаты поиска

Содержание Latitiude E6500

Отзывы:

Похожие инструкции для Latitiude E6500

Бренды по названию

Популярные бренды

Dell Latitiude E6500, Руководство по обслуживанию

Результаты поиска

Содержание Latitiude E6500

Отзывы:

Похожие инструкции для Latitiude E6500

Бренды по названию

Популярные бренды