manualshive.com logo in svg

Dell Latitiude E6500, Руководство по обслуживанию

Поделиться
Скачать
Dell Latitiude E6500 Скачать руководство пользователя страница 31

 

Replacing an FCM  

 

 

 

 

 

 

 

 

1.

Slide the FCM card into the connector.  
 

 

  

2.

Press the card down to the alignment post and hold in position.  
 

 

  

3.

Replace the screw in the FCM card.  
 

 

  

4.

Replace the left hinge cover (see 

Replacing the Hinge Covers

).  

 

 

  

5.

Replace the bottom of the base assembly (see 

Removing the Bottom of the Base Assembly

).  

 

 

  

6.

Replace the battery (see 

Replacing the Battery

).  

 

Back to Contents Page

 

 

 

 

CAUTION: 

The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors on the card and on the system 

board, and realign the card.

 

CAUTION: 

To avoid damage to the FCM card, ensure the cables are not under the card when you replace the card.

 

CAUTION: 

The Mini-Card slot has WPAN/UWB/FCM silk-screened inside the slot. Do not install FCM cards in any other Mini-Card slot.

Содержание Latitiude E6500









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды