Dell G16 7620 Скачать руководство пользователя страница 54

Страница: 54 / 79

About this task

The following image indicates the location of the ethernet and audio board and provides a visual representation of the removal
procedure.

1. Follow the procedure in

Before working inside your computer

2. Remove the

3. Remove the

4. Remove the

5. Remove the

6. Remove the

7. Remove the

NOTE:

The system board can be removed as an assembly with the memory modules, fan and heat-sink assembly,

ethernet and audio board, and USB board attached.

Steps

1. Turn the system-board assembly over.
2. Remove the two screws (M2x4) that secure the ethernet and audio board to the system board.
3. Disconnect and remove the ethernet and audio board from the system board.

Installing the ethernet and audio board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the ethernet and audio board and provides a visual representation of the
installation procedure.

Removing and installing components

Содержание G16 7620
















































































Результаты поиска

Содержание G16 7620

Отзывы:

Dell G16 7620, Руководство по обслуживанию, Страница: 54 / 79

Результаты поиска

Содержание G16 7620

Отзывы: