Dell G16 7620 Скачать руководство пользователя страница 51

Страница: 51 / 79

Installing the fan and heat-sink assembly (NVIDIA GeForce RTX
3050 Ti graphics card)

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

NOTE:

This procedure only applies to computers shipped with a NVIDIA GeForce 3050 Ti graphics card.

About this task

The following image indicates the location of the fan and heat-sink assembly and provides a visual representation of the
installation procedure.

NOTE:

If either the system board or the heat sink is replaced, use the thermal pad that is provided in the kit to ensure that

thermal conductivity is achieved.

Steps

1. Place the fan and heat-sink assembly on the system board and align the screw holes on the fan and heat-sink assembly with

the screw holes on the system board.

2. In reverse sequential order (6>5>4>3>2>1), replace the six screws (M2x4) that secure the fan and heat-sink assembly to

the system board.

3. Turn the system-board assembly over.

Next steps

1. Install the

system board

2. Install the

wireless card

Removing and installing components

Содержание G16 7620
















































































Результаты поиска

Содержание G16 7620

Отзывы:

Dell G16 7620, Руководство по обслуживанию, Страница: 51 / 79

Результаты поиска

Содержание G16 7620

Отзывы: