Dell G16 7620 Скачать руководство пользователя страница 50

Страница: 50 / 79

NOTE:

The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you

touch it.

2. Remove the

3. Remove the

4. Remove the

5. Remove the

6. Remove the

7. Remove the

NOTE:

The system board can be removed as an assembly with the memory modules, fan and heat-sink assembly,

ethernet and audio board, and USB board attached.

NOTE:

This procedure only applies to computers shipped with a NVIDIA GeForce 3050 Ti graphics card.

About this task

The following image indicates the location of the fan and heat-sink assembly and provides a visual representation of the removal
procedure.

Steps

1. Turn the system-board assembly over.
2. In sequential order (1>2>3>4>5>6), remove the six screws (M2x4) that secure the fan and heat-sink assembly to the

system-board assembly.

3. Lift the fan and heat-sink assembly off the system-board assembly.

Removing and installing components

Содержание G16 7620
















































































Результаты поиска

Содержание G16 7620

Отзывы:

Dell G16 7620, Руководство по обслуживанию, Страница: 50 / 79

Результаты поиска

Содержание G16 7620

Отзывы: