manualshive.com logo in svg

Dell EMC PowerEdge T440, Инструкция по установке и обслуживанию

Поделиться
Скачать
Dell EMC PowerEdge T440 Скачать руководство пользователя страница 98

Figure 47. x8 drive backplane

1

ODD power connector

2

backplane P4 power connector

3

backplane sideband signal connector

4

Mini SAS SAS_A0

5

Mini SAS SAS_B0

Removing a hard drive backplane

Prerequisites

CAUTION: 

To prevent damage to the drives and backplane, you must remove the hard drives from the system before removing 

the backplane.

CAUTION: 

You must note the number of each hard drive and temporarily label them before removal so that you can replace them 

in the same locations.

1

Follow the safety guidelines listed in 

Safety instructions

.

2

Follow the procedure listed in 

Before working inside your system

.

3

If installed, remove the bezel.

4

Remove all the drives.

5

Remove the air shroud.

Steps

1 

Disconnect the data, signal, and power cables from the backplane.

NOTE: 

For the x8 backplane, press the SAS connector and push the connector toward the top of the system to release 

the SAS cable from the backplane.

2 

Pull the release pin and holding the pin, lift the backplane out of the system.

98

Dell EMC PowerEdge T440 Installation and Service Manual
Installing and removing system components

Содержание EMC PowerEdge T440





























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды