Dell EMC PowerEdge T440 Скачать руководство пользователя

Страница: 53 / 156

Network Settings

You can use the

Network Settings

screen to modify UEFI PXE, iSCSI, and HTTP boot settings. The network settings option is available

only in the UEFI mode.

NOTE:

The BIOS does not control network settings in the BIOS mode. For the BIOS boot mode, the optional Boot ROM of the

network controllers handles the network settings.

Viewing Network Settings

To view the

Network Settings

screen, perform the following steps:

Turn on, or restart your system.

Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

On the

System Setup Main Menu

screen, click

System BIOS

On the

System BIOS

screen, click

Network Settings

Network Settings screen details

The

Network Settings

screen details are explained as follows:

Option

Description

UEFI PXE Settings

Enables or disables the device. When enabled, a UEFI PXE boot option is created for the device.

UEFI HTTP Settings Enables or disables the device. When enabled, a UEFI HTTP boot option is created for the device.

UEFI iSCSI Settings

Enables you to control the configuration of the iSCSI device.

Table 31. UEFI iSCSI Settings screen details

Option

Description

iSCSI Initiator Name

Specifies the name of the iSCSI initiator in IQN format.

iSCSI Device1

Enables or disables the iSCSI device. When disabled, a
UEFI boot option is created for the iSCSI device
automatically. This is set to

Disabled

by default.

iSCSI Device1 Settings

Enables you to control the configuration of the iSCSI
device.

Dell EMC PowerEdge T440 Installation and Service Manual

Pre-operating system management applications

Содержание EMC PowerEdge T440





























































































































































Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды

Dell EMC PowerEdge T440, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды