Dell EMC PowerEdge T440 Скачать руководство пользователя

Страница: 20 / 156

Table 6. NIC indicator codes

Status

Condition

Link and activity indicators are off

The NIC is not connected to the network.

Link indicator is green and activity indicator is blinking green The NIC is connected to a valid network at its maximum port speed and

data is being sent or received.

Link indicator is amber and activity indicator is blinking
green

The NIC is connected to a valid network at less than its maximum port
speed and data is being sent or received.

Link indicator is green and activity indicator is off

The NIC is connected to a valid network at its maximum port speed and
data is not being sent or received.

Link indicator is amber and activity indicator is off

The NIC is connected to a valid network at less than its maximum port
speed and data is not being sent or received.

Link indicator is blinking green and activity is off

NIC identify is enabled through the NIC configuration utility.

Power supply unit indicator codes

AC power supply units (PSUs) have an illuminated translucent handle that serves as an indicator. The indicator shows whether power is
present or if a power fault has occurred.

Figure 11. AC PSU status indicator

AC PSU status indicator/handle

Table 7. AC PSU status indicator codes

Power indicator codes

Condition

Green

A valid power source is connected to the PSU and the PSU is operational.

Blinking amber

Indicates a problem with the PSU.

Not illuminated

Power is not connected to the PSU.

Blinking green

When the firmware of the PSU is being updated, the PSU handle blinks green.

CAUTION:

Do not disconnect the power cord or unplug the PSU when updating firmware. If

firmware update is interrupted, the PSUs do not function.

Blinking green and turns off When hot-plugging a PSU, the PSU handle blinks green five times at a rate of 4 Hz and turns off. This

indicates a PSU mismatch with respect to efficiency, feature set, health status, or supported voltage.

Dell EMC PowerEdge T440 Installation and Service Manual
Dell EMC PowerEdge T440 overview

Содержание EMC PowerEdge T440





























































































































































Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды

Dell EMC PowerEdge T440, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды