Dell EMC PowerEdge T440 Скачать руководство пользователя

Страница: 46 / 156

Option

Description

Boot Settings

Specifies options to specify the Boot mode (BIOS or UEFI). Enables you to modify UEFI and BIOS boot settings.

Network Settings

Specifies options to manage the UEFI network settings and boot protocols.
Legacy network settings are managed from the

Device Settings

menu.

Integrated Devices

Specifies options to manage integrated device controllers and ports, specifies related features and options.

Serial
Communication

Specifies options to manage the serial ports, its related features and options.

System Profile

Settings

Specifies options to change the processor power management settings, memory frequency.

System Security

Specifies options to configure the system security settings, such as system password, setup password, Trusted
Platform Module (TPM) security, and UEFI secure boot. It also manages the power button on the system.

Redundant OS
Settings

Specifies the options to configure the Redundant OS settings.

Miscellaneous
Settings

Specifies options to change the system date and time.

System Information

You can use the

System Information

screen to view system properties such as Service Tag, system model name, and the BIOS version.

Viewing System Information

To view the

System Information

screen, perform the following steps:

Turn on, or restart your system.

Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

On the

System Setup Main Menu

screen, click

System BIOS

On the

System BIOS

screen, click

System Information

System Information details

The

System Information

screen details are explained as follows:

Option

Description

System Model
Name

Specifies the system model name.

System BIOS
Version

Specifies the BIOS version installed on the system.

System
Management
Engine Version

Specifies the current version of the Management Engine firmware.

System Service Tag

Specifies the system Service Tag.

Dell EMC PowerEdge T440 Installation and Service Manual
Pre-operating system management applications

Содержание EMC PowerEdge T440





























































































































































Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды

Dell EMC PowerEdge T440, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды