Dell EMC PowerEdge T440 Скачать руководство пользователя

Страница: 59 / 156

Option

Description

C1E

Enables or disables the processor to switch to a minimum performance state when it is idle. This option is set to

Enabled

by default.

C States

Enables or disables the processor to operate in all available power states. This option is set to

Enabled

by default.

Write Data CRC

Enables or disables the Write Data CRC. This option is set to

Disabled

by default.

Collaborative CPU
Performance
Control

Enables or disables the CPU power management option. When set to

Enabled

, the CPU power management is

controlled by the OS DBPM and the System DBPM (DAPC). This option is set to

Disabled

by default.

Memory Patrol
Scrub

Sets the memory patrol scrub frequency. This option is set to

Standard

by default.

Memory Refresh
Rate

Sets the memory refresh rate to either 1x or 2x. This option is set to

by default.

Uncore Frequency

Enables you to select the

Processor Uncore Frequency

option.

Dynamic mode

enables the processor to optimize power resources across the cores and uncore during runtime.

The optimization of the uncore frequency to either save power or optimize performance is influenced by the
setting of the

Energy Efficiency Policy

option.

Energy Efficient
Policy

Enables you to select the

Energy Efficient Policy

option.

The CPU uses the setting to manipulate the internal behavior of the processor and determines whether to target
higher performance or better power savings. This option is set to

Balanced Performance

by default.

Number of Turbo
Boost Enabled
Cores for Processor
1

NOTE:

If there are two processors installed in the system, you will see an entry for Number of Turbo

Boost Enabled Cores for Processor 2.

Controls the number of turbo boost enabled cores for Processor 1. The maximum number of cores is enabled by
default.

Monitor/Mwait

Enables the Monitor/Mwait instructions in the processor. This option is set to

Enabled

for all system profiles,

except

Custom

by default.

NOTE:

This option can be disabled only if the C States option in the Custom mode is set to disabled.

NOTE:

When C States is set to Enabled in the Custom mode, changing the Monitor/Mwait setting does

not impact the system power or performance.

CPU Interconnect
Bus Link Power
Management

Enables or disables the CPU Interconnect Bus Link Power Management. This option is set to

Enabled

by default.

PCI ASPM L1 Link
Power
Management

Enables or disables the PCI ASPM L1 Link Power Management. This option is set to

Enabled

by default.

Dell EMC PowerEdge T440 Installation and Service Manual

Pre-operating system management applications

Содержание EMC PowerEdge T440





























































































































































Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды

Dell EMC PowerEdge T440, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды