Dell D28M Скачать руководство пользователя

Страница: 88 / 94

Amber LED state

White LED state

System state

Notes

process. Appropriate mem
modules detected but failure has
occurred.

BIOS state 4

BIOS Post code (Old LED
pattern 0100) Combine PCI
device config or failure with
video sub sytem config or failure.
BIOS to eliminate 0101 video
code.

BIOS state 5

BIOS Post code (Old LED
pattern 0110) Combine storage
and USB config or failure. BIOS
to eliminate 0111 USB code.

BIOS state 6

BIOS Post code (Old LED
pattern 1000) MEM config, no
memory detected.

BIOS state 7

BIOS Post code (Old LED
pattern 1001) Fatal Motherboard
error.

BIOS state 8

BIOS Post code (Old LED
pattern 1010) Mem config,
modules incompatible or invalid
config.

BIOS state 9

BIOS Post code (Old LED
pattern 1011) combine "Other
pre-video activity and resource
configuration codes. BIOS to
eliminate 1100 code.

BIOS state 10

BIOS Post code (Old LED
pattern 1110) Other pre-post
activity, routine subsequent to
video init.

Diagnostic error messages

Table 22. Diagnostic error messages

Error messages

Description

AUXILIARY DEVICE FAILURE

The touchpad or external mouse may be faulty. For an external
mouse, check the cable connection. Enable the

Pointing Device

option in the System Setup program.

BAD COMMAND OR FILE NAME

Ensure that you have spelled the command correctly, put spaces in
the proper place, and used the correct path name.

CACHE DISABLED DUE TO FAILURE

The primary cache internal to the microprocessor has failed.

Contact Dell

CD DRIVE CONTROLLER FAILURE

The optical drive does not respond to commands from the
computer.

DATA ERROR

The hard drive cannot read the data.

DECREASING AVAILABLE MEMORY

One or more memory modules may be faulty or improperly seated.
Reinstall the memory modules or, if necessary, replace them.

DISK C: FAILED INITIALIZATION

The hard drive failed initialization. Run the hard drive tests in

Dell

Diagnostics

Troubleshooting

Содержание D28M































































































Результаты поиска

Содержание D28M

Отзывы:

Похожие инструкции для D28M

Бренды по названию

Популярные бренды

Dell D28M, Руководство по обслуживанию

Результаты поиска

Содержание D28M

Отзывы:

Похожие инструкции для D28M

Бренды по названию

Популярные бренды