Dell D28M Скачать руководство пользователя страница 10

Страница: 10 / 94

Disassembly and reassembly

Recommended tools

The procedures in this document require the following tools:

•

Phillips #0 screwdriver

•

Phillips #1 screwdriver

•

Philips #2 screwdriver

•

Plastic scribe

•

Hex screwdriver

Screw list

NOTE:

When removing screws from a component, it is recommended to note the screw type, the quantity of screws,

and then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type
is restored when the component is replaced.

NOTE:

Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when

replacing a component.

NOTE:

Screw color may vary with the configuration ordered.

Table 1. Screw list

Component

Secured to

Screw type

Quantity

Screw image

Wireless card

System board

M2x3

Solid-state drive

System board

M2x4

Intel Optane memory
module

System board

M2x4

Power-supply unit

Chassis

#6-32

Ports bezel

Chassis

#6-32

System board

Chassis

#6-32

Processor fan and heat-
sink assembly

System board

Captive screw

VR heat sink

System board

Captive screw

Disassembly and reassembly

Содержание D28M































































































Результаты поиска

Содержание D28M

Отзывы:

Похожие инструкции для D28M

Бренды по названию

Популярные бренды

Dell D28M, Руководство по обслуживанию

Результаты поиска

Содержание D28M

Отзывы:

Похожие инструкции для D28M

Бренды по названию

Популярные бренды