Dell D28M Скачать руководство пользователя

Страница: 32 / 94

Installing the wireless card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

NOTE:

To avoid damage to the wireless card, do not place any cables under it.

About this task

The following images indicate the location of the wireless card and provides a visual representation of the installation procedure.

Steps

1. Align the notch on the wireless card with the tab on the wireless-card slot.
2. Slide the wireless card at an angle into the wireless-card slot.
3. Connect the antenna cables to the wireless card.

The following table provides the antenna-cable color scheme for the wireless card supported by your computer.

Table 2. Antenna-cable color scheme

Connectors on the wireless card

Antenna-cable color

Main (white triangle)

White

Disassembly and reassembly

Содержание D28M































































































Результаты поиска

Содержание D28M

Отзывы:

Похожие инструкции для D28M

Бренды по названию

Популярные бренды

Dell D28M, Руководство по обслуживанию

Результаты поиска

Содержание D28M

Отзывы:

Похожие инструкции для D28M

Бренды по названию

Популярные бренды