manualshive.com logo in svg

Dell Command Line Interface, Руководство пользователя, Страница: 74 / 226

Поделиться
Скачать
Dell Command Line Interface Скачать руководство пользователя страница 74

74

omconfig: Managing Components Using the Instrumentation Service

As with other commands, the CLI issues an error message if you do not have a chassis 2 (the main 
chassis=0). The CLI allows you to issue commands only for the system configuration you have.

omconfig chassis leds

Use the 

omconfig chassis leds

 command to specify when to flash a chassis fault LED or chassis 

identification LED and allow you to clear the LED for the system's hard drive. Table 4-10 shows the valid 
parameters for the command.

omconfig chassis memorymode

Use the 

omconfig chassis memorymode

 command to specify the redundancy mode you want to use for 

your system’s memory in case of memory errors.

Redundant memory enables a system to switch to other available memory modules if unacceptable errors 
are detected in the modules it is currently using. The 

omconfig chassis memorymode 

command allows 

you to disable redundancy; when you disable redundancy, you instruct the system not to switch to other 
available memory modules when the module the system is using begins to encounter errors. If you want 
to enable redundancy, you must choose among spare, mirror, and RAID. 

Spare mode disables a bank of system memory in which a correctable memory event is detected, enables 
the spare bank, and copies all the data from the original bank to the spare bank. Spare bank requires at 
least three banks of identical memory; the operating system does not recognize the spare bank.

Mirror mode switches to a redundant copy of memory when an uncorrectable memory event is detected. 
After switching to the mirrored memory, the system does not switch back to the original system memory 
until the next reboot. The operating system does not recognize half of the installed system memory in 
this mode. 

RAID mode provides an extra level of memory checking and error recovery at the expense of some 
memory capacity.

Table 4-11 shows the valid parameters for the command.

Table 4-10.

omconfig chassis leds

name=value pair 1

name=value pair 2

Description

index=<

n>

NA

Number of the chassis where the LED resides (defaults to 
chassis 0, main system chassis).

led=fault

severity=warning | critical

Select to flash the LED either when a warning event occurs or 
when a critical event occurs.

led=hdfault

action=clear

Sets the number of faults for the hard drive back to zero (0).

led=identify

flash=off | on

time-out=<

n>

Sets the chassis identification LED to off or on. Set the 
time-out value for the LED to flash to a number of seconds.

Содержание Command Line Interface



































































































































































































































Отзывы:

Нет отзывов