Dell Command Line Interface Скачать руководство пользователя страница 28

Страница: 28 / 226

omreport: Viewing System Status Using the Instrumentation Service

Table 3-2.

BIOS Setup Parameters

Parameters

Description

Bezel

Displays whether the bezel removal intrusion check during system
reboot is enabled or disabled.

Bootsequence

Displays the device that is used to boot the system.

Console Redirection

Displays if the BIOS screen is redirected over a particular serial port
or if it is turned off.

Console Redirection After Boot

Displays whether console redirection after system reboot is enabled
or disabled.

Diskette

Displays whether the diskette is disabled, auto enabled, or read only.

Demand Based Power
Management (DBS)

Displays whether DBS is enabled or disabled on the system.

Dual NIC

Displays whether NIC 1 and NIC 2 with PXE is enabled or disabled.

External Serial Connector

Displays whether the external serial connector is mapped to COM
port 1 or COM port 2 or a Remote Access Device.

Console Redirection Failsafe Baud
Rate

Displays the setting for console redirection failsafe baud rate.

IDE

Displays whether the drive is enabled or disabled.

IDE Primary Drive 0

Displays whether the device is automatically detected and enabled
or if the device is disabled.

IDE Primary Drive 1

Displays whether the device is automatically detected and enabled
or if the device is disabled.

Intrusion

Displays whether the intrusion check is enabled or disabled during
system boot.

Mouse

Displays whether the mouse is enabled or disabled.

NIC 1

Displays whether the first NIC is enabled (with or without PXE) or
disabled during system boot.

NIC 2

Displays whether the second NIC is enabled (with or without PXE)
or disabled during system boot.

Numlock

Displays whether the keypad can be used as number keys.

Parallel port address

Displays whether the address is located on LPT1, LPT2, and LPT3,
or if it is disabled.

Parallel port mode

Displays the setting associated with the parallel port.

Primary SCSI

Displays whether the device is on or off.

RAID on motherboard

Displays whether RAID-on-motherboard is detected as a RAID
device, a SCSI device, or if the device is disabled during system boot.

Содержание Command Line Interface



































































































































































































































Результаты поиска

Содержание Command Line Interface

Отзывы:

Похожие инструкции для Command Line Interface

Бренды по названию

Популярные бренды

Dell Command Line Interface, Руководство пользователя

Результаты поиска

Содержание Command Line Interface

Отзывы:

Похожие инструкции для Command Line Interface

Бренды по названию

Популярные бренды