manualshive.com logo in svg

Deka unigy II SPACESAVER Non-Interlock AVR 45 AH, Инструкция по установке и эксплуатации

Поделиться
Скачать
Deka unigy II SPACESAVER Non-Interlock AVR 45 AH Скачать руководство пользователя страница 6

10.  Module layout should be compared to battery string layout 

diagram and all hardware should be checked for proper 

torque before proceeding. Consult “Hardware Torque 

Requirements” (pg b.4) for proper torque values.

Safety Shield Bracket Assembly

1.  

Safety shield brackets are to be installed at the outside  

corners of every 2 modules starting from the bottom and 

working towards the top. This is to be repeated for each stack 

in the battery system. For stacks containing odd number of 

modules an additional set of safety shield brackets will be 

required to be installed at the top of the module. Use  

3/8-16 x 2.50

"

 hardware to install brackets. Bracket should  

be flush with side of module to ensure correct safety shield 

alignment. Tighten, do not torque hardware.

b.6

Содержание unigy II SPACESAVER Non-Interlock AVR 45 AH

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды