Deka unigy II SPACESAVER Non-Interlock AVR 45 AH Скачать руководство пользователя страница 26

Страница: 26 / 32

b.26

APPENDIX D

Voltage Compensation Chart

2mV per ºC

Standby (Float) Application Charge Current Limits Non-Interlock

AVR45 Series

AVR95 Series

AVR75 Series

** = Using minimum charge current will extend recharge time and increase risk of battery being undercharged

°C

Float Refresh /

Equalize

°F

>35 2.230

2.380

>95

2.232

2.382

93.2

2.234

2.384

91.4

2.236

2.386

89.6

2.238

2.388

87.8

2.240

2.390

86.0

2.242

2.392

84.2

2.244

2.394

82.4

2.246

2.396

80.6

2.248

2.398

78.8

2.250

2.400

77.0

2.252

2.402

75.2

2.254

2.404

73.4

2.256

2.406

71.6

2.258

2.408

69.8

2.260

2.410

68.0

2.262

2.412

66.2

2.264

2.414

64.4

2.266

2.416

62.6

2.268

2.418

60.8

2.270

2.420

59.0

2.272

2.422

57.2

2.274

2.424

55.4

2.276

2.426

53.6

2.278

2.428

51.8

<10 2.280

2.430

<50

Cell Type Max. Charge

Current (A)

Min. Charge

Current (A)**

AVR45-5

16.5

4.9

AVR45-7

24.7

7.4

AVR45-9

32.9

9.9

AVR45-11

41.1

12.3

AVR45-13

49.4

14.8

AVR45-15

57.6

17.3

AVR45-17

65.8

19.7

AVR45-19

74.1

22.2

AVR45-21

82.3

24.7

AVR45-23

90.5

27.2

AVR45-25

98.7

29.6

AVR45-27

107

32.1

AVR45-29

115

34.6

AVR45-31

123

37.0

AVR45-33

132

39.5

Cell Type Max. Charge

Current (A)

Min. Charge

Current (A)**

AVR95-7

51.5

15.4

AVR95-9

68.7

20.6

AVR95-11

85.8

25.7

AVR95-13

103

30.9

AVR95-15

120

36.0

AVR95-17

137

41.2

AVR95-19

154

46.3

AVR95-21

172

51.5

AVR95-23

189

56.6

AVR95-25

206

61.8

AVR95-27

223

66.9

AVR95-29

240

72.1

AVR95-31

257

77.2

AVR95-33

275

82.4

Cell Type Max. Charge

Current (A)

Min. Charge

Current (A)**

AVR75-5

27.3

8.2

AVR75-7

41.0

12.3

AVR75-9

54.6

16.4

AVR75-11

68.3

20.5

AVR75-13

81.9

24.6

AVR75-15

95.6

28.7

AVR75-17

109

32.8

AVR75-19

123

36.9

AVR75-21

137

41.0

AVR75-23

150

45.0

AVR75-25

164

49.1

AVR75-27

177

53.2

AVR75-29

191

57.3

AVR75-31

205

61.4

AVR75-33

218

65.5

Содержание unigy II SPACESAVER Non-Interlock AVR 45 AH

































Результаты поиска

Содержание unigy II SPACESAVER Non-Interlock AVR 45 AH

Отзывы:

Бренды по названию

Популярные бренды

Deka unigy II SPACESAVER Non-Interlock AVR 45 AH, Инструкция по установке и эксплуатации

Результаты поиска

Содержание unigy II SPACESAVER Non-Interlock AVR 45 AH

Отзывы:

Бренды по названию

Популярные бренды