manualshive.com logo in svg

Deka unigy II SPACESAVER Non-Interlock AVR 45 AH, Инструкция по установке и эксплуатации

Поделиться
Скачать
Deka unigy II SPACESAVER Non-Interlock AVR 45 AH Скачать руководство пользователя страница 14

b.14

Side Termination

Consult battery string layout diagram for termination location.
1.   Remove module bolts (3/8-16 x 1.25") from the module where 

side termination is to be installed. If safety shield bracket is at 

one of these locations, retain for later use.

2.   Install plastic side terminal bracket in location where bolts 

were removed in previous step. Use 3/8-16 x 4.50" bolts. Bolts 

should be installed loosely for future adjustments. Replace  

safety shield bracket at same location from previous step.

SLEEVE  

SPACER

SLEEVE  

SPACER

4.   Install side terminal connector to battery posts using 1/4- 20 

bolts. Bolts should be installed loosely for future adjustments.

3.  

The side terminal may be located at the bottom module. Slot 

in lower arm of side terminal bracket slips over tab in base 

plate. The upper side terminal bracket connection should be 

attached as called out in previous section.

1CU / 2CU CONNECTOR PACKAGE 

(single connector)

     Review the “Connector Packages” chart (pg b.8) to ensure 

the correct connector package has been supplied.

Содержание unigy II SPACESAVER Non-Interlock AVR 45 AH

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды