Degelman M28 Скачать руководство пользователя страница 7

Страница: 7 / 45

-5-

142657 - Manure Spreader (17-March-2016)

1. Read and understand the Operator’s

Manual and all safety signs before

operating, maintaining or adjusting

the Manure Spreader.

2. Install and properly secure all shields and

guards before operating. Use hitch pin with a

mechanical locking device.

3. Have a first-aid kit available for use

should the need arise and know

how to use it.

4. Have a fire extinguisher available

for use should the need arise and

know how to use it.

5. Wear appropriate protective gear. This list

includes but is not limited to:

• A hard hat
• Protective shoes with slip resistant soles
• Protective glasses or goggles
• Heavy gloves
• Wet weather gear
• Hearing protection
• Respirator or filter mask

6. Clear the area of people, especially small

children, and remove foreign objects from the

machine before starting and operating.

7. Do not allow riders.

8. Stop tractor engine, set park brake, remove

ignition key and wait for all moving parts to

stop before servicing, adjusting, repairing or

unplugging.

9. Review safety related items with all operators

annually.

YOU

are responsible for the safe operation and

maintenance of your Degelman Manure Spreader.

YOU

must ensure that you and anyone else who

is going to operate, maintain or work around

the Spreader be familiar with the operating and

maintenance procedures and related

SAFETY

information contained in this manual.

This manual will take you step-by-step through

your working day and alerts you to all good safety

practices that should be adhered to while operating

this equipment.

Remember,

YOU

are the key to safety. Good safety

practices not only protect you but also the people

around you. Make these practices a working

part of your safety program. Be certain that

EVERYONE

operating this equipment is familiar

with the recommended operating and maintenance

procedures and follows all the safety precautions.

Most accidents can be prevented. Do not risk injury

or death by ignoring good safety practices.

• Manure Spreader owners must give

operating instructions to operators or

employees before allowing them to operate

the Spreader, and at least annually

thereafter.

• The most important safety device on this

equipment is a SAFE operator. It is the

operator’s responsibility to read and

understand ALL Safety and Operating

instructions in the manual and to follow

these. All accidents can be avoided.

• A person who has not read and understood

all operating and safety instructions is

not qualified to operate the machine. An

untrained operator exposes himself and

bystanders to possible serious injury or

death.

• Do not modify the equipment in any way.

Unauthorized modification may impair the

function and/or safety and could affect the

life of the equipment.

• Think SAFETY! Work SAFELY!

Safety

SAFETY

GENERAL SAFETY

Содержание M28














































Результаты поиска

Содержание M28

Отзывы:

Бренды по названию

Популярные бренды

Degelman M28, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание M28

Отзывы:

Бренды по названию

Популярные бренды