Degelman M28 Скачать руководство пользователя страница 28

Страница: 28 / 45

-26-

142657 - Manure Spreader (17-March-2016)

REAR GATE CYLINDERS

Hitch Pole Components

Rear Gate Cylinders

122570 - Cylinder, Dump - 2 x 72 x 1-1/4 (2)

122572 - Barrel (1)

(comes with Port Plugs)

141633 - Port Plug, 9/16 ORB (2)

122508 - Lock Ring (1)

122506 - Open Cap (1)

122521 - Seal Kit (1)

122581 - Piston (1)

118441 - Lock nut, 7/8”

UNF unitorque (1)

122577 - Rod & Pin Eye (1)

246700 - Hitch Pole Assy (1)

118911 - Lock Nut, 1” (2)

118456 - Lock nut, 1” (2)

118422 - Lock nut,

3/4” (1)

118050 - Bolt, 3/4”x 3” (1)

118634 - Bolt,

1”x 12” (2)

118775 - Flat Washer,

3/4” SAE (1)

246507 - Bushing,

1-3/16” (1)

246506 - Washer, Support 1/2” (2)

133131 - Spring, Rubber (5)

118845 - Roll Pin, 5/16”

x 2-1/2” (2)

240286 - Bushing, Mach

1-1/2” NOM (2)

118266 - Bolt,

1” x 8” (2)

118464 - Nut, 1” UNC GR8 (1)

118073 - Bolt, 1” x 3-1/2” UNC GR8 (1)

116256 - Safety Chain Assembly, 20,200 lbs (1)

116255 - Safety Chain, Bundle (1)

comes with...

246503 - Pin, Hitch Pole (2)

118615 - Flat washer, 1” x 3-1/8” x 1/4” (1)

118510 - Lock washer, 1” (1)

118520 - Flat washer, 1” (1)

132036 - Jack,

Sidewind,

12,000 lbs (1)

141618 - Adaptor, 3/4

JIC-m x 1-1/16 ORB (1)

118125 - Bolt, 1/4”x 2-1/2” (2)

118402 - Nut, 1/4 (2)
118533 - Lock Washer, 1/4 (2)

141617 - 90° Elbow, 3/4

JIC-m x 1-1/16 ORB(1)

141121 - Valve, EFC (1)

HITCH POLE COMPONENTS

246515 - Valve Assembly (1)

c/w Valve, Hydraulic Fittings, & Wiring

118511 - Flat washer, 3/8 (2)
246723 - Lid, Electrical (1)

118005 - Bolt, 3/8” x 1” (2)

246526 - Light Enhancing Module (1)

mounts with...

117499 -

Nut, #6-32 (2)

118588 -

Washer,

Rubber (2)

117498 -Screw,

Mach #6-32 (2)

124044 - Hitch Assy, CAT.3 with 2” Ball (1)

124045 - Ball, Insert 2” (1)
124046 - Ball, Insert 1-1/2” Optional (1)

Содержание M28














































Результаты поиска

Содержание M28

Отзывы:

Бренды по названию

Популярные бренды

Degelman M28, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание M28

Отзывы:

Бренды по названию

Популярные бренды