manualshive.com logo in svg

Degelman M28, Руководство оператора и каталог запасных частей

Поделиться
Скачать
Degelman M28 Скачать руководство пользователя страница 36

-34-

142657 - Manure Spreader     (17-March-2016)

BEATER CORE & PIN ASSEMBLY

118027 - Bolt, 5/8 x 2 (30)

246628 - Pin, 2 x 7-3/4 (15)

118447 - Lock Nut, 5/8 (30)

 

Beater Timing Mark Location

Beaters should be timed 180° 

opposite each other to avoid 

damage caused by paddle contact.

246805 - Paddle, 

Bottom Row (3)

246623 - Beater Core 

Assembly (2)

(without paddles)

Note:

 Previous paddle design used a 5-1/8” 

bushing and 

single-lip

 seals: 

    246279 - Seal, Wiper - Single Lip (2)

Updated design uses a slightly shorter 5” 

bushing to accomodate new 

dual-lip

 seals. 

The dual-lip seals will not fit properly with the 

previous 5-1/8” bushing.

Rear Frame & Beater Components

246279 - Seal, Wiper (2)

117179 - Bushing (1)

 

WARNING

:

 

When installing/replacing 

complete beater assembly, ensure bottom plate 

timing mark positions of 

both beater assemblies are 

opposite (180°) to avoid 

paddle contact and damage.

246625 - Paddle Assembly, 

Hammer Head (12)

246782 - Seal, Wiper 

- Dual Lip (2)

117179 - Bushing (1)

 

NOTE

:

 

It is recommended 

to replace all three paddles 

from a row at the same time 

to maintain proper balance 

of beater assembly.

 

NOTE

:

 

Wear tip 

paddles must be installed 

with tips facing rotation.

118935 - Bolt, 5/8 

x 2-1/2 GR8 (8)

117581 - Lock Nut, 

5/8 Flanged (8)

246693 - 

Wear Tip (4)

OPTIONAL COMPONENTS: 

246691 - Paddle Assembly, 

Hammer Head - Carbide Tip (12)

246782 - Seal, Wiper 

- Dual Lip (2)

117179 - Bushing (1)

Содержание M28














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды