Degelman M28 Скачать руководство пользователя страница 27

Страница: 27 / 45

-25-

142657 - Manure Spreader (17-March-2016)

Walking Axle & Wheel Components

OPTION - LARGER WHEEL/AXLE PACKAGE

131565 - Rim, 26 x 25.0 DC - 10H - STR (1)

127015 - Valve Stem, TR618A (1)

131566 - Tire, 750/60 R26 (1)

131567 - Wheel Assembly,

750/60 R26 - LH (2)

comes with...

131568 - Wheel Assembly,

750/60 R26 - RH (2)

comes with...

246981 - Walking Wheel Assembly (2)

118422 - Lock Nut, 3/4 (2)

131358 - Hub (1)

comes with Bearing Cups

131359 - Bearing, Cup - Inner (1)

131360 - Bearing, Cup - Outer (1)

131362 - Bearing, Cone - Outer (1)

131366 - Gasket, Dust Cap - 4 Hole (1)

131364 - Dust Cap, DC28 - 4 Hole (1)

118586 - Flat Washer, 2-1/8 ID (1)

118711 - Slotted Nut, 2-12 UNF (1)

117551 -Roll Pin,

3/8 x 3 (1)

118641 - Bolt, 5/16 x 1/2 (4)

118712 - Nut, Wide Base

3/4 UNF GR8 (10)

118158 - Bolt,

3/4 x 7 (2)

131397 - Spindle, S1020 (2)

131361 - Bearing, Cone - Inner (1)

131363 - Dust Seal, CR43771 (1)

HUB/SPINDLE COMPONENTS

131396 - Hub/Spindle Assembly (4)

comes with...

Recommended Wheel Bolt

Torque Specs:

280-300 ft·lbs (380-405 N·m) -dry

220-240 ft·lbs (300-325 N·m) -lub.

Note:

Recheck torque on wheel

bolts after a couple of hours, and

following day.

Recommended pressure:

58 psi (400 kPa)

Note:

Larger wheel option replaces the walking

axles and tires only. All other items are the

same as the standard tire option (Spindles,

wear washers, rod assembly and hardware.)

Содержание M28














































Результаты поиска

Содержание M28

Отзывы:

Бренды по названию

Популярные бренды

Degelman M28, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание M28

Отзывы:

Бренды по названию

Популярные бренды