Degelman M28 Скачать руководство пользователя страница 35

Страница: 35 / 45

-33-

142657 - Manure Spreader (17-March-2016)

TOP BEATER FRAME & BEARINGS

117215 - Bearing Unit, Assembly (2)

comes with...

118403 - Nut, 3/8 (16)

118503 - Lock Washer, 3/8 (16)

117478 - Bolt, 5/16 x 4-1/2 (3)

118302 - Capscrew, Self-Tap - 3/8 x 1 (4)

246620 - Shield, Top

Beater Bearing (1)

246618 - Frame,

Top Beater (1)

246274 - Bearing Guard Assembly (4)

118795 - Bolt, 5/8 x 2-1/4 (8)

118129 - Bolt, 3/8 x 1-1/4 (16)

118703 - Lock Nut, 5/16 (3)

Rear Frame & Beater Components

Note:

Ensure Bearing Bolts are installed in

the direction shown in this diagram.

118537 - Flat Washer, 5/8 F436 (8)

LOWER BEATER FRAME AND GEARBOX

246880 - Frame,

Beater Deck (1)

170447 - Gearbox Assembly (1)

118508 - Lock Washer, 5/8 (4)

118514 - Flat Washer, 5/8 (4)

118026 - Bolt, 5/8 x 2 (4)

118407 - Nut, 5/8 (4)

117483 - Nut, M14 (16)
117484 - Lock Washer, M14 (16)
118098 - Bolt, M14 x 50 P8.8 (16)

Note:

Models with a Serial Number from

1000-1009 require 2” thick spacers

between Gearbox ends and deckframe.

(246684 - Spacer Kit)

(Part Breakdown

on pg. 29)

117195 - Housing - 4 hole (1)

(comes with retainer rings

117198 - Retainer Ring

)

117196 - Bearing, Insert

- 2-7/16 (1)

117197 - Adapter Sleeve (1)

(comes with nut & lock ring)

IMPORTANT:

After nut is properly

tightened, bend tab(s) of lock ring

onto nut.

IMPORTANT:

When installing,

ensure adaptor sleeve is locked onto

shaft and is not slipping.

Correct

Snap Ring

Locations

Содержание M28














































Результаты поиска

Содержание M28

Отзывы:

Бренды по названию

Популярные бренды

Degelman M28, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание M28

Отзывы:

Бренды по названию

Популярные бренды