DeDietrich Innovens MCA 25/28 BIC Скачать руководство пользователя страница 87

Страница: 87 / 124

7.4.6.

Checking combustion

The check on combustion is done by measuring the percentage of

/CO

in the flue gas discharge flue. To do this, proceed as follows:

1. Unscrew the plug of the flue gas measurement point.
2. Connect the flue gas analyser.

CAUTION

Ensure that the opening around the sensor is completely

sealed when taking measurements.

3. Set the boiler to full load.

See chapter: "Setting the air/gas

ratio (Full load)", page 53. The boiler is now operating at full

load. Measure the percentage of CO

and compare this value with

the checking values given.

4. Set the boiler to part load.

See chapter: "Setting the air/gas

ratio (Part load)", page 54. The boiler is now operating on part

load. Measure the percentage of CO

and compare this value with

the checking values given.

T001581-A

MCA 25/28 BIC

7. Checking and maintenance

15/06/12 - 300022159-001-01

Содержание Innovens MCA 25/28 BIC





























































































































Результаты поиска

Содержание Innovens MCA 25/28 BIC

Отзывы:

Бренды по названию

Популярные бренды

DeDietrich Innovens MCA 25/28 BIC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Innovens MCA 25/28 BIC

Отзывы:

Бренды по названию

Популярные бренды