dbx DriveRack 240 Скачать руководство пользователя страница 62

Страница: 62 / 69

DriveRack™ User Manual

Appendix A

DriveRack

™

Specifications ( 240 DriveRack™)

Inputs

Number of Inputs:

Connectors:

XLR, Euroblock

Type:

Electronically balanced/RF filtered

Impedance:

>40k

Ω

Maximum Input Level:

Hardware selectable for +30, +22, +14, dBu

CMRR:

>40 dB typical, >55 dB at 1kHz

Outputs

Number of Outputs:

Connectors:

XLR, Euroblock

Type:

Electronically balanced, RF filtered

Impedance:

Ω

Max Output Level:

+25.5 dBu into 1k

Ω

+22dBu into 600

Ω

System Performance

Type:

dbx Type IV™ Conversion System

Dynamic Range line:

>105 dB unweighted, 108 dB A-weighted

Type IV™ dynamic range:

120 dB with transient material,
A-weighted, 22kHz BW
118 dB with transient material,
unweighted, 22kHz BW
112 dB typical with program material,
A-weighted, 22kHz BW

Sample Rate:

48kHz

Word length:

24 bits

Latency:

74.9 samples typical

THD + Noise:

0.005% typical at +4dBu, 1kHz, 0dB input gain

Frequency Response:

20Hz- 20kHz, +/-0.5dB

Interchannel Crosstalk:

<-100dB at 1kHz

Functions:
Pre EQ
Type:

One 31-band Graphic EQ per input channel, or
9 band Parametric EQ per input channel
Both inputs linkable

Range:

+/-12 dB range

Pre Delay
Length:

1.0 seconds/channel
Both inputs linkable

Crossover

Type:

Wire(1x1, 1x2, 1x3, 1x4) Filter (1x1, 1x2, 1x3, 1x4),
Crossovers: 1x2, 1x3, 1x4, 2x3, 2x4, 2x4(Dual Band)

Filter Type:

Butterworth, Bessel, or Linkwitz-Riley

Slope:

6, 12, 18 or 24 dB/octave for Butterworth or Bessel filters
12 or 24 dB/octave for Linkwitz-Riley filters

Post EQ

Type:

Parametric

Number:

4 EQ bands per output channel

Range:

+/-12 dB range

A.5 Specifications

Содержание DriveRack 240






































































Результаты поиска

Содержание DriveRack 240

Отзывы:

Похожие инструкции для DriveRack 240

Бренды по названию

Популярные бренды

dbx DriveRack 240, Руководство пользователя

Результаты поиска

Содержание DriveRack 240

Отзывы:

Похожие инструкции для DriveRack 240

Бренды по названию

Популярные бренды