dbx DriveRack 240 Скачать руководство пользователя страница 64

Страница: 64 / 69

DriveRack™ User Manual

Appendix A

DriveRack

™

Word length:

24 bits

Latency:

74.9 samples typical

THD + Noise:

0.005% typical at +4dBu, 1kHz, 0dB input gain

Frequency Response:

20Hz- 20kHz, +/-0.5dB

Interchannel Crosstalk:

<-100dB at 1kHz

Functions:
Pre EQ
Type:

One 31-band Graphic EQ per input channel, or
9 band Parametric EQ per input channel
Both inputs linkable

Range:

+/-12 dB range

Pre Delay
Length:

1.0 seconds/channel
Both inputs linkable

Crossover

Type:

Wire(1x1, 1x2, 1x3, 1x4) Filter (1x1, 1x2, 1x3, 1x4),
Crossovers: 1x2, 1x3, 1x4, 2x3, 2x4, 2x4(Dual Band)

Filter Type:

Butterworth, Bessel, or Linkwitz-Riley

Slope:

6, 12, 18 or 24 dB/octave for Butterworth or Bessel filters
12 or 24 dB/octave for Linkwitz-Riley filters

Post EQ

Type:

Parametric

Number:

4 EQ bands per output channel

Range:

+/-12 dB range
All 4 channels are linkable

Dynamics

Type:

Compressor/Limiter with PeakStopPlus™

Attack/Release:

Program Dependent

Linking:

All 4 parameters are linkable

Post Delay (Driver Alignment)

Length:

365.32 ms per output channel
All 4 parameters are linkable

Phase Compensation
Number:

One per output channel

Amount:

0-360 degrees phase shift

Miscellaneous

Output

GUI:

RS-232 interface for computer display and configuration

ROM Upgrade:

Flash upgradeable through RS-232

Power Requirements

Watts:

100-240V - 50/60 Hz
35 Watts

Dimensions

Dimensions:

Height- 1.75” X Width- 19” X Depth 7.90”

Weight

8 lbs.

Shipping Weight:

9.5 lbs.

Содержание DriveRack 240






































































Результаты поиска

Содержание DriveRack 240

Отзывы:

Похожие инструкции для DriveRack 240

Бренды по названию

Популярные бренды

dbx DriveRack 240, Руководство пользователя

Результаты поиска

Содержание DriveRack 240

Отзывы:

Похожие инструкции для DriveRack 240

Бренды по названию

Популярные бренды