Davicom DM9000 Скачать руководство пользователя страница 4

Страница: 4 / 55

DM9000

ISA to Ethernet MAC Controller with Integrated 10/100 PHY

Final

Version: DM9000-DS-F02

June 26, 2002

3. Features

■

Supports processor interface: byte/word/dword of

I/O command to internal memory data operation

■

Integrated 10/100M transceiver

■

Supports MII and reverses MII interface

■

Supports back pressure mode for half-duplex

mode flow control

■

IEEE802.3x flow control for full-duplex mode

■

Supports wakeup frame, link status change and

magic packet events for remote wake up

■

Integrated 4K dword SRAM

■

Supports automatically load vendor ID and

product ID from EEPROM

■

Supports 4 GPIO pins

■

Optional EEPROM configuration

■

Very low power consumption mode:

–

Power reduced mode (cable detection)

–

Power down mode

–

Selectable TX drivers for 1:1 or 1.25:1

transformers for additional power reduction.

■

Compatible with 3.3V and 5.0V tolerant I/O

■

100-pin LQFP with CMOS process

Содержание DM9000
























































Результаты поиска

Содержание DM9000

Отзывы:

Похожие инструкции для DM9000

Бренды по названию

Популярные бренды

Davicom DM9000, Руководство пользователя

Результаты поиска

Содержание DM9000

Отзывы:

Похожие инструкции для DM9000

Бренды по названию

Популярные бренды