Davey DynaDrive DD160-19 Скачать руководство пользователя страница 27

Страница: 27 / 32

Mechanical seal

Carbon/ceramic

O-rings

EPDM

Plugs

316 stainless steel

Motor shell and lantern bracket

Aluminium with baked polyester powder coat finish

Motor feet

Xenoy

Fan cowl/rear foot (DD60-10, DD90-11)

Polypropylene

Adaptor VSD

Polypropylene

5-way tee piece

304 stainless steel

Pump coupling to 5-way tee piece

Brass

10. MAINTENANCE

ATTENTION: Automatic resets may allow the pump to restart without warning. Always

disconnect the pump motor from the electrical supply before maintenance or repairs.

When servicing or attending pump and/or controllers, always ensure power is switched

off and lead unplugged. Electrical connections should be serviced only by qualified

persons. If the electrical supply lead of this pressure system is damaged, it must be

replaced by the manufacturer, or an appointed representative. Under no circumstances

should the DynaDrive be disassembled by other than qualified tradespersons. Failure to

observe this warning may expose persons to the possibility of personal injury and may

also result in damage to other property. Do not dismantle spring under pressure.

IMPORTANT: Do not use hydrocarbon based or hydrocarbon propelled sprays around

the electrical components of this pump. During servicing, use only approved, non-

petrochemical based o-ring and gasket lubrication. If unsure, consult your Davey

representative for advice. For protection, DynaDrive monitors input current and will shut

down the pump motor in the event of an over load.

10.1 Periodic pressure tank checks

Depending on the quality of the pumped water, from time to time your tank may require flushing to remove

settled fines such as mud or sand. If sand, or mud can stay in the tank it will accelerate wear on the internal

lining and shorten your tanks life. Safely disconnect the tank from the water supply, discharge all air from the

tank and flush the tank several times with clean water. Once the flushing water is clean, reconnect the tank

and recharge the air as described in the pressure tank section of the installation chapter.
A tank in good order will not leak, but over time due to damage through rough handling, impacts or grit and/

or impurities in the water the tank shell may fail and/or leak. Should the tank leak or show signs of possible

failure the tank should be immediately disconnected and replaced.

Содержание DynaDrive DD160-19

































Результаты поиска

Содержание DynaDrive DD160-19

Отзывы:

Похожие инструкции для DynaDrive DD160-19

Бренды по названию

Популярные бренды

Davey DynaDrive DD160-19, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DynaDrive DD160-19

Отзывы:

Похожие инструкции для DynaDrive DD160-19

Бренды по названию

Популярные бренды