manualshive.com logo in svg

Datasensing SH4 BASE-STANDARD, Руководство по продукции, Страница: 92 / 103

Поделиться
Скачать
Datasensing SH4 BASE-STANDARD Скачать руководство пользователя страница 92

CASCADE SYSTEM

84

   SH4 BASE-STANDARD

CONNECTION

In order to connect SH4 units in a cascade system, follow the steps below:

1. Connect  the  M12-5  poles 

female

  connector  of  the  MASTER  unit  to  the  M12-5

poles 

male

 connector of following slave unit.

2. Same way a LAST SLAVE can be connected to the MID SLAVE.

RX connection

NOTE: When the distance between units doesn't allow a direct connection

an optional M12 male to M12 female 5 pole cable may be used up to 10 m

cable length. Refer to Accessories appendix to see the available models.

NOTE: When using a SH4-XX-XXXX-C-5-5 model as LAST SLAVE the M12

female connector will provide muting inputs with same pinout of MASTER

unit  (depending  on  the  configuration  for  advanced  models).  For  more

details  please  refer  to  SH4-XX-XXXX-SM-8-5  or  SH4-XX-XXXX-A-12-5

connections on the respective Product Reference Guide.

NOTE: When using an SH4-XX-XXXX-A-12-5 model as MASTER unit, pin 11

(GP_IO2) from 12 poles male connector must be left floating.

NOTE: See chapter “Connections” for consult the connector’s pin-out.

M12 8 or 12 pin, male

M12 5 pin

female

M12 5 pin

male

M12 5 pin

female

M12 5 pin

male

M12 5 pin female or none

Содержание SH4 BASE-STANDARD








































































































Отзывы:

Нет отзывов