Datasensing SH4 BASE-STANDARD Скачать руководство пользователя страница 48

Страница: 48 / 103

FUNCTIONS

SH4 BASE-STANDARD

EDM

(Standard models only)

The External Device Monitoring (EDM) function controls external devices by verifying

the OSSDs status. To correctly use this function user must connect EDM input to a N.C.

to 24V contact of the device to control (forced guide relay).

Figure 8: EDM wiring

The function controls the N.C. contact switching according to the changes of the OSSD

status.
The timing diagram below explains the relationship between the cause (OSSDs) and the

effect (EDM), with the maximum permissible delay.

Figure 9: EDM function timing



350 ms (time between OSSD OFF-ON transition and EDM test)



100 ms (time between OSSD ON-OFF transition and EDM test)

(two different times for the mechanical contact driven by a spring)

Configuration

The configuration of EDM is done by connecting the EDM SEL signal (

pin 3

green

) as

described below:

• EDM SELECTION connected to 0V (floating): EDM ENABLED
• EMD SELECTION connected to 24V: EDM DISABLED

24Vdc

OSSD_1

OSSD_2

EDM

OSSD_1

OSSD_2

EDM

ESPE

Safety MPCE

forced guide

relais

EDM ENABLED

EDM DISABLED

floating

OFF

24Vdc

0Vdc

OSSDs

STATUS

EDM

Содержание SH4 BASE-STANDARD








































































































Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы:

Datasensing SH4 BASE-STANDARD, Руководство по продукции, Страница: 48 / 103

Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы: