Datasensing SH4 BASE-STANDARD Скачать руководство пользователя страница 2

Страница: 2 / 103

Datasensing S.r.l.

Strada S. Caterina 235

41122 Modena

Italy

Tel. +39 059 420411

Fax +39 059 253973

duced, stored in or introduced into a retrieval system, or transmitted in any form or by any means, or for any

purpose, without the express written permission of Datasensing S.r.l. Owners of Datasensing products are

hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the

purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices,

including copyright notices, contained in this documentation and shall ensure that all notices appear on any

reproductions of the documentation. Electronic versions of this document may be downloaded from the

Datasensing website (www.datasensing.com).

Disclaimer

Datasensing has taken reasonable measures to provide information in this manual that is complete and

accurate, however, Datasensing shall not be liable for technical or editorial errors or omissions contained

herein, nor for incidental or consequential damages resulting from the use of this material. Datasensing

reserves the right to change any specification at any time without prior notice.

Trademarks

Datasensing and the Datasensing logo are trademarks of Datasensing S.r.l.

Patents

See

w ww.patents.datasensing.com

for patent list.

This product is covered by one or more of the following patents:
Utility patents: IT1363719, IT1427575, US10188007

ORIGINAL INSTRUCTIONS (ref. 2006/42/EC)

Содержание SH4 BASE-STANDARD








































































































Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы:

Datasensing SH4 BASE-STANDARD, Руководство по продукции, Страница: 2 / 103

Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы: