Datasensing SH4 BASE-STANDARD Скачать руководство пользователя страница 15

Страница: 15 / 103

PRECAUTIONS TO BE OBSERVED FOR THE CHOICE AND INSTALLATION

PRODUCT REFERENCE GUIDE

PRECAUTIONS TO BE OBSERVED FOR THE CHOICE AND

INSTALLATION

• Use only matched emitter and receiver pairs with same serial no.
• The outputs (OSSD) of the ESPE must be used as machine stopping devices and

not as command devices.

• The machine must have its own START command.
• The dimension of the smallest object to be detected must be larger than the reso

lution level of the device.

• The ESPE must be installed in an environment complying with the characteristics

indicated in

Technical Data, starting on page 55

• The ESPE must not be installed close to strong and/or flashing light sources, in par

ticular close to the front window of receiving unit.

• The presence of intense electromagnetic disturbances could affect device’s cor

rect operation.

• This condition shall be carefully assessed with the advice of DATALOGIC Technical

Service.

• The operating distance of the device can be reduced in presence of smog, fog or

airborne dust.

• A sudden change in environment temperature, with very low minimum peaks, can

generate a small condensation layer on the lenses and thus jeopardize correct

operation.

CAUTION: Make sure that the protection level assured by the light curtain

device is compatible with the real danger level of the machine to be con

trolled, according to EN ISO 13849-1: 2015 or EN 62061:2005/A2: 2015.

Содержание SH4 BASE-STANDARD








































































































Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы:

Datasensing SH4 BASE-STANDARD, Руководство по продукции, Страница: 15 / 103

Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы: