Datasensing SH4 BASE-STANDARD Скачать руководство пользователя страница 100

Страница: 100 / 103

SH4 BASE-STANDARD

APPENDIX G

GLOSSARY

AOPD (Active optoelectronic protective device)

Its detection function is achieved thanks to the use of optoelectronic receivers and

emitters detecting the optical beams interruptions inside the device caused by an

opaque object present inside the specified detecting area.

An active optoelectronic protective device (AOPD) can operate both in emitter-receiver

mode and in retro-reflective light curtains.

Block condition (=BREAK)

Status of the light curtain taking place when a suitably-sized opaque object interrupts

one or several light curtain beams.
Under these conditions, OSSD1 and OSS2 light curtain outputs are simultaneously

switched OFF within the device response time.

Crossing hazard

Situation under which an operator crossing the area controlled by the safety device and

this latter stops and keeps the machine stopped until the hazard is eliminated, and then

enters the dangerous area. Now the safety device could not be able to prevent or avoid

an unexpected restart of the machine with the operator still present inside the danger

ous area.

Dangerous area

Area representing an immediate or imminent physical hazard for the operator working

inside it or who could get in contact with it.

Detection capability (or Resolution)

The minimum dimension which an opaque object must have in order to interrupt at

least one beams of the ESPE whatever is position across the protected height.

Detection zone

Zone within which a specified test piece will be detected by the ESPE

EDM (External device monitoring)

Device used by the ESPE to monitor the status of the external command devices.

Emitter (TX)

Unit emitting infrared beams, consisting of a set of optically-synchronized LEDs. The

emitting unit, combined with the receiving unit (installed in the opposite position), gen

erates an optical “curtain”, i.e. the detecting area.

Содержание SH4 BASE-STANDARD








































































































Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы:

Datasensing SH4 BASE-STANDARD, Руководство по продукции, Страница: 100 / 103

Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы: