Datasensing SH4 BASE-STANDARD Скачать руководство пользователя страница 16

Страница: 16 / 103

INSTALLATION

SH4 BASE-STANDARD

HOW TO CHOOSE THE DEVICE

There are at least three different main characteristics that should be considered when

choosing a safety light curtain, after having evaluated the risk assessment.

Detection capability

The detection capability (or resolution) of the device is the minimum diameter that an

opaque object must have in order to obscure at least one of the beams that constitute

the detection zone and to actuate the sensing device.
The resolution is related to the part of the body to be protected.

As shown in the following figure the resolution only depends on the geometrical charac

teristics of the lenses, diameter and distance between centers, and is independent of

any environmental and operating conditions of the safety light curtain.

Figure 1: Detection capability

The resolution value is obtained applying the following formula:

R = I + d

where:
I = Interaxes between two adjacent optics
d = Lens diameter

R = 14 mm

Finger protection

R = 30 mm

Hand protection

Operating distance

Pro

tec

ted

eig

opaque

object

Содержание SH4 BASE-STANDARD








































































































Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы:

Datasensing SH4 BASE-STANDARD, Руководство по продукции, Страница: 16 / 103

Результаты поиска

Содержание SH4 BASE-STANDARD

Отзывы: