Datamax Mark II E-4205e Скачать руководство пользователя

Страница: 54 / 72

Appendix B – Internal Menu

B.4.1 Auto Media Sensor Calibration

Auto Media Sensor Calibration automatically establishes the optimum sensing values for the media you are

using in the printer.



Before calibrating, be sure the media sensor is set for the appropriate media type; also, ensure that

the Printhead Carrier Assembly is latched down and the cover is closed.

To automatically calibrate the media sensor, proceed as follows:

1. With the desired media loaded, hold the

button while powering up the printer. Continue to hold the

button until the PAUSED Light turns off then release it.

2. Next press the

button.

The printer will feed approximately ten inches of media to calculate the TOF

Delta and Low values to be used.

3. Upon completion, one of the following Indicators will flash five times to denote the result of the auto

calibration attempt:

PAUSED Light = Successful calibration. Proceed to Step 5.

FAULT Light = Unsuccessful calibration. Proceed to Section B.4.2.



If you wish to discard the changes and revert back to the previous calibration simply turn off the

printer before Step 5.

4. Now save the changes and resume Normal mode by pressing the

buttons simultaneously. Wait

until the PAUSED Light goes off before printing.

Содержание Mark II E-4205e









































































Результаты поиска

Содержание Mark II E-4205e

Отзывы:

Похожие инструкции для Mark II E-4205e

Бренды по названию

Популярные бренды

Datamax Mark II E-4205e, Руководство оператора

Результаты поиска

Содержание Mark II E-4205e

Отзывы:

Похожие инструкции для Mark II E-4205e

Бренды по названию

Популярные бренды