Datamax Mark II E-4205e Скачать руководство пользователя

Страница: 10 / 72

Chapter 2 – Printer Setup

2.2.2 Interface Connection

The printer can be connected to the host via a USB, serial, or parallel cable.

An optional Wired or Wireless LAN interface is also available. For information on using this interface, refer to

Appendix C.

Serial

Connection

Parallel

Connection

USB

Connection

To Host

LAN Connection

(optional)

2.2.3 Interface Cables

Choose a connection method that will best serve your purpose:



To connect the printer to the host’s serial (RS-232C) interface use an acceptable cable

configuration, as shown below (contact your reseller for ordering information).

Part # 32-2483-01

Part # 32-2301-01



To connect the printer to the host’s parallel interface use a Centronics

parallel cable.



To connect the printer to the host’s USB interface use a standard USB cable.

Note that the printer has a versatile communications feature: When connected to more than one interface, the

printer will automatically connect to the first port (serial, parallel, or USB) from which valid data is received.

After this connection has been made, the printer’s power must be cycled ‘Off’ and ‘On’ to change the interface

connection.

Содержание Mark II E-4205e









































































Результаты поиска

Содержание Mark II E-4205e

Отзывы:

Похожие инструкции для Mark II E-4205e

Бренды по названию

Популярные бренды

Datamax Mark II E-4205e, Руководство оператора

Результаты поиска

Содержание Mark II E-4205e

Отзывы:

Похожие инструкции для Mark II E-4205e

Бренды по названию

Популярные бренды