Datamax Mark II E-4205e Скачать руководство пользователя

Страница: 28 / 72

Chapter 3 – Printer Operation

3.8.3 Hex Dump Label

The Hex Dump Label is a useful tool in the diagnosis of problems including communications handshaking and

DPL syntax errors. To generate a Hex Dump Label the printer enters into Hex Dump Mode. In this mode, all

data sent to the printer will be immediately output in hexadecimal code, along with the printable ASCII

equivalents. To decode this information, the

Class Series Programmer’s Manual

is an essential reference. As a

final note, many software programs use bit mapping to construct the label, making diagnosis of this data

difficult. Contact Datamax-O’Neil

Technical Support with any questions.

To enter Hex Dump Mode and print a Hex Dump Label, proceed as follows:

With the printer off, loaded with media (at least 4 inches wide) and ribbon (if printing with thermal transfer

media), press and hold the

button while turning the printer on. Continue holding the

button until the

PAUSED Light turns off. Now, all data received by the printer will be output in hexadecimal code, as shown

below.

To exit the Hex Dump Mode, turn the printer off.

Содержание Mark II E-4205e









































































Результаты поиска

Содержание Mark II E-4205e

Отзывы:

Похожие инструкции для Mark II E-4205e

Бренды по названию

Популярные бренды

Datamax Mark II E-4205e, Руководство оператора

Результаты поиска

Содержание Mark II E-4205e

Отзывы:

Похожие инструкции для Mark II E-4205e

Бренды по названию

Популярные бренды