Datamax Mark II E-4205e Скачать руководство пользователя страница 25

Страница: 25 / 72

Chapter 3 – Printer Operation

3.7.3 Standard Calibration

The Standard Calibration can be performed using the DMXConfig Utility,

(see section 3.5 for more information

on DMXConfig)

or using the front panel buttons

(see Appendix B for more information).

Once you have installed the DMXConfig utility and the printer is properly loaded with media:

1. Connect the host to the printer with a serial

or parallel cable.

2. Turn on the printer.

3. Launch the DMXConfig utility.

4. Query the printer by using the ‘Query Printer’

toolbar button (top-left). This will connect to

the printer and get the current printer

settings.

5. Select the “Sensor Calibration” Tab and then

click the “Media Calibration Wizard” button.

When prompted click “OK” to start the

calibration wizard.

6. The Calibration Wizard will now prompt you to

‘Load Stock’. Be sure the media is properly

loaded in the printer. Close the printhead and

click “OK”.

Содержание Mark II E-4205e









































































Результаты поиска

Содержание Mark II E-4205e

Отзывы:

Бренды по названию

Популярные бренды

Datamax Mark II E-4205e, Руководство оператора

Результаты поиска

Содержание Mark II E-4205e

Отзывы:

Бренды по названию

Популярные бренды