Datalogic QuickScan Lite QW2400 Скачать руководство пользователя

Страница: 228 / 288

References

236

QuickScan™ Lite QW2400

ACK NAK Options

This enables/disables the ability of the scanner to support the RS-232 ACK/

NAK protocol. When configured, the scanner and/or host sends an “ACK” when

it receives data properly, and sends “NAK” when the data is in error.
Options are:

• Disable

• Enable for label transmission — The scanner expects an ACK/NAK

response from the host when a label is sent

• Enable for host-command acknowledge — The scanner will respond with

ACK/NAK when the host sends a command

• Enable for label transmission and host-command acknowledge

ACK Character

This setting specifies an ASCII character or hex value to be used as the ACK

character. ASCII characters or any hex value from 0 to 0xFF can be selected.

1. Determine the desired character or value.
2. Use the

ASCII Chart on page 297

on the inside back cover of this manual to

find the hex equivalent for the desired character/value.

3. Go to

page 29

and scan ENTER/EXIT PROGRAMMING MODE to enter Pro-

gramming Mode.

4. Scan the bar code: SELECT ACK CHARACTER SETTING.
5. Scan the appropriate two alphanumeric characters from the keypad in

Appendix D, Keypad

, that represent the desired character/value determined

above. The second character will cause a two-beep indication.

6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit.

See the table below for examples of how to set this feature.

Table 3. ACK Character Setting Examples

NOTE

Setting to previously defined characters such as XON, XOFF, or host com-
mands conflicts with normal operation of these characters. 8-bit data is
not recognized when the option

Data Bits on page 22

has been set as 7

Data Bits.

STEP

ACTION

EXAMPLES

Desired Character/Value

ACK

Hex equivalent from

ASCII

Chart on page 297

0x06

0x24

0x40

0x3E

Scan ENTER/EXIT PROGRAMMING MODE

Scan SELECT ACK CHARACTER SETTING

Scan Two Characters from

Appendix D, Keypad

‘0’ and ‘6’

‘2’ and ‘4’

‘4’ and ‘0’

‘3’ AND ‘E’

Scan ENTER/EXIT PROGRAMMING MODE

Содержание QuickScan Lite QW2400

































































































































































































































































































Результаты поиска

Содержание QuickScan Lite QW2400

Отзывы:

Похожие инструкции для QuickScan Lite QW2400

Бренды по названию

Популярные бренды

Datalogic QuickScan Lite QW2400, Руководство по продукции

Результаты поиска

Содержание QuickScan Lite QW2400

Отзывы:

Похожие инструкции для QuickScan Lite QW2400

Бренды по названию

Популярные бренды