Datalogic QuickScan Lite QW2400 Скачать руководство пользователя

Страница: 14 / 288

Setup

QuickScan™ Lite QW2400

Connect Host Interface

The scanner kit you ordered to match your interface should provide a compati-

ble cable for your installation. If this is not so, contact

Technical Support

The scanner can communicate using the following interfaces:

RS-232 Serial Connection

Turn off power to the terminal/PC and connect the scanner to the terminal/PC

serial port via the RS-232 cable as shown in Figure 3. If the terminal will not

support POT (Power Off the Terminal) to supply scanner power, use the

approved power supply (AC Adapter). Plug the AC Adapter barrel connector into

the socket on the RS-232 cable connector and the AC Adapter plug into a stan-

dard power outlet.

RS-232:

The scanner can communicate with a standard or Wincor-Nixdorf (W-N)

RS-232 host.

RS-232 OPOS:

This interface is used for OPOS/UPOS/JavaPOS systems.

Keyboard Wedge Connection

The Keyboard Wedge cable has a ‘Y’ connection from the scanner. Connect the

female to the male end from the keyboard and the remaining end at the key-

board port at the terminal/PC.

Keyboard Wedge (KBW) :

When connected using this interface, the host interprets

scanned data as keystrokes and supports several international keyboards (for

the Windows

environment). See

"Country Mode"

on page 36 for a full listing.

USB Connection

Connect the scanner to a USB port on the terminal/PC using the correct USB

cable for the interface type you ordered.

USB :

Select to communicate either by USB OEM, USB COM STD, or USB Keyboard

interface types by scanning the appropriate interface type bar codes available in

this manual. The default interface is USB-KBD, or RS-232-STD.

Содержание QuickScan Lite QW2400

































































































































































































































































































Результаты поиска

Содержание QuickScan Lite QW2400

Отзывы:

Похожие инструкции для QuickScan Lite QW2400

Бренды по названию

Популярные бренды

Datalogic QuickScan Lite QW2400, Руководство по продукции

Результаты поиска

Содержание QuickScan Lite QW2400

Отзывы:

Похожие инструкции для QuickScan Lite QW2400

Бренды по названию

Популярные бренды