manualshive.com logo in svg

Danfoss VLT MCD 600, Руководство по эксплуатации, Страница: 134 / 140

Поделиться
Скачать
Danfoss VLT MCD 600 Скачать руководство пользователя страница 134

•

•

•

•

•

•
•

•

•

•

•

•
•

•
•

Symptom

Probable cause/suggested solution

Remote LCP shows

Awaiting data

The LCP is not receiving data from the control PCB. Check the cable connection.

The soft starter does
not control the mo-
tor correctly during
start.

Start performance may be unstable when using a low motor FLC setting (

parameter 1-2 Motor Full

Load Current

).

Install power factor correction (PFC) capacitors on the supply side of the soft starter. Disconnect the
capacitors during starting and stopping. To control a dedicated PFC capacitor contactor, connect the
contactor to a programmable relay set to Run.
High levels of harmonics on the mains supply side can affect the soft starter performance. If drives
are installed nearby, check that they are properly grounded and filtered.

Motor does not
reach full speed.

If the start current is too low, the motor does not produce enough torque to accelerate to full speed.
The soft starter may trip on excess start time.

N O T I C E

Make sure that the motor starting parameters are appropriate for the application and that the inten-
ded motor starting profile is used. If a programmable input is set to 

Motor Set Select

, check that the

corresponding input is in the expected state.

Check if the load is jammed. Check the load for severe overloading or a locked rotor situation.

Soft stop ends too
quickly.

The soft stop settings may not be appropriate for the motor and load. Review the settings.
If the motor is lightly loaded, soft stop has limited effect.

After selecting adap-
tive control, the mo-
tor used an ordinary
start and/or the sec-
ond start was differ-
ent to the first.

The first adaptive control start is constant current so that the soft starter can learn from the motor
characteristics. Subsequent starts use adaptive control.

PowerThrough does
not operate when se-
lected

The soft starter trips on 

Lx-Tx Shorted

 on the first start attempt after control power is applied. Power-

Through does not operate if control power is cycled between starts.

Parameter settings
cannot be stored.

Make sure to save the new value by pressing [Menu/Store] after adjusting a parameter setting. If
pressing [Back], the change is not saved. The soft starter does not show a confirmation.
Check that 

parameter 10-7 Adjustment Lock

 is set to 

Read & Write

. If the parameter is set to 

Read Only

,

settings can be viewed but not changed.

USB full

The USB drive may not have enough free space available for the selected function.
The file system on the USB drive may not be compatible with the soft starter. The VLT® Soft Start-
erMCD 600 supports FAT32 file systems. The USB functions of the MCD 600 are not compatible with
NTFS file systems.

USB missing

A USB function has been selected in the menu, but the product cannot detect a USB drive. Check that the
USB drive has been inserted in the port.

File missing

A USB function has been selected in the menu, but the required file cannot be found.
Save/load master parameters uses a file called Master_Parameters.par at the top level of the USB
drive. For these functions to work correctly, do not move or rename this file.

AQ262141844215en-000401 / 175R1174

130 | Danfoss A/S © 2020.12

Troubleshooting

VLT® Soft Starter MCD 600

Operating Guide

Содержание VLT MCD 600













































































































































Отзывы:

Нет отзывов