Danfoss VLT 5042 Скачать руководство пользователя

Страница: 62 / 123

VLT® 5000 Crane

Programming

■

Inputs & Outputs

When running in Crane profile, the digital inputs are

hard coded. This means that there are no functions to

choose between, as the settings cannot be changed.

The table below shows the inputs in question.

Digital inputs

Terminal no.

parameter

300

301

302

303

304

305

306

307

Value:

Crane ready

(CRANE READY)

[30]

Positioning

(POSITIONING)

[30]

Start lowering

(START LOWERING)

[30]

Start hoisting

(START HOISTING)

[30]

Quick stop

(QUICK STOP)

[30]

Gear choice

(GEAR CHOICE)

[30]

Load contact 1

(LOAD CONTACT 1)

[30]

Load contact 2

(LOAD CONTACT 2)

[30]

The functions are described further below:

Crane ready

input signal for system ready.

Positioning

is selected if the frequency converter

is to work in positioning mode. Positioning mode

is only available when running in remote control.

If the signal is removed, the frequency converter

is to operate in normal mode.

Start lowering

is selected when the frequency

converter is to lower a load. This function is

only available in remote control.

Start hoisting

this function enables hoisting of a load

when the frequency converter is in remote control.

Quick stop

ramps the motor speed down to zero

with the selected quick ramp time.

Gear choice

is used whenever the gear is changed

in order to perform a load estimation. The function

is only available in remote control.

Load contact 1

is the high load contact, which is used

for load monitoring when operating in remote control.

Load contact 2

is the low load contact,

which is also used for load monitoring when

operating in remote control.

✭

= factory setting. () = display text [] = value for use in communication via serial communication port

MG.50.N4.02 - VLT is a registered Danfoss trademark

Содержание VLT 5042




























































































































Результаты поиска

Содержание VLT 5042

Отзывы:

Похожие инструкции для VLT 5042

Бренды по названию

Популярные бренды

Danfoss VLT 5042, Руководство по эксплуатации

Результаты поиска

Содержание VLT 5042

Отзывы:

Похожие инструкции для VLT 5042

Бренды по названию

Популярные бренды