Danfoss VLT 5000 Series Скачать руководство пользователя страница 11

Страница: 11 / 63

VLT® 5000/ 5000 FLUX/ 6000 HVAC/
8000 AQUA PROFIBUS

The indicated lengths in the tables are valid

on the condition that bus cables with the

following properties are used:

- Impedance:

135 to 165 Ohm at a measuring
frequency of 3 to 20 MHz

- Resistance:

< 110 Ohm/km

- Capacity:

< 30 pF/m

- Damping:

max. 9 dB across the entire
cable length

- Cross-section:

max. 0.34 mm pursuant to
AWG 22

- Wire type:

twisted pair, 1 x 2 or 2 x 2 or 1
x 4 conductors

- Shielding

copper-braided or braided and
foil laminated

It is recommended to use the same cable type

throughout the entire network in order to avoid

mismatches of the impedance.

The figures in the following description indicate the

maximum permitted number of stations in each

segment. These figures do not refer to the station

addresses, since each station in the network must

have an unambiguous address.

Segment 1

Segment 2

Segment 3

Segment 4

MG.90.G1.02 - VLT is a registered Danfoss trademark

Содержание VLT 5000 Series
































































Результаты поиска

Содержание VLT 5000 Series

Отзывы:

Бренды по названию

Популярные бренды

Danfoss VLT 5000 Series, Руководство по эксплуатации

Результаты поиска

Содержание VLT 5000 Series

Отзывы:

Бренды по названию

Популярные бренды