Danfoss Turbocor TT-300 Скачать руководство пользователя страница 58

Страница: 58 / 68

Service Monitor User Manual

Danfoss Turbocor Compressors Inc.

ECD-00007M Rev. 1

Discharge Pressure

The actual discharge gauge pressure at the compressor flange
as measured by the discharge pressure transducer.

Suction Temperature

The actual suction temperature at the compressor flange as
measured by the suction temperature/pressure transducer.

Discharge Temperature

The actual discharge temperature at the compressor flange as
measured by the discharge temperature/pressure transducer.

Cavity Temperature

Temperature of the superheated gas moving past the shaft.

Entering Air/Water Temp

Temperature as measured from the 10K thermistor connected
to the terminals marked “ENTRY” on the Chiller Interface
module.

Leaving Air/Water Temp

Temperature as measured from the 10K thermistor connected
to the terminals marked “LEAVE” on the Chiller Interface
module.

24VDC Supply

Regulated 24V DC voltage as measured from the Backplane.

InterLock Status

Interlock status:
either opened (denoted by 1.0) or closed (denoted by 0.0).

Surge Speed

Minimum compressor speed [RPM].

Choke Speed

Maximum compressor speed [RPM].

Stepper #1 PV

Controlled variable maintained by the stepper motor #1 output.

Stepper #1 Position

Ratio of the actual number of steps sent to the stepper motor
over the maximum number of steps the motor is allowed to
drive. Range: 0%-100%.

Stepper #2 PV

Controlled variable maintained by the stepper motor #2 output.

Stepper #2 Position

Ratio of the actual number of steps sent to the stepper motor
over the maximum number of steps the motor is allowed to
drive. Range: 0%-100%.

Cooling Solenoid Status

Cooling solenoid status:
either open (denoted by 1.0) or closed (denoted by 0.0).

Axial Force

Current required to counteract axial unbalance force [Amps].

FX Force

Current required to counteract front x unbalance force [Amps].

FY Force

Current required to counteract front y unbalance force [Amps].

BX Force

Current required to counteract rear x unbalance force [Amps].

BY Force

Current required to counteract rear y unbalance force [Amps].

Actual Speed

Actual shaft speed in RPM.

Desired Speed

Commanding shaft speed in RPM (always higher than the
actual shaft speed).

Motor Amps (Inverter Side)

Current output from the IGBT Inverter to the motor (torque-
generating current component).

3 Phase Power (kW)

3-phase AC input power (mains input)

Inverter Temperature

Inverter temperature as measured by thermistor mounted
under the IGBT Inverter.

Front Orbit Average

Percentile indicating the average front orbit displacement.

Table 21 Trending Parameters (Continued)

Parameter

Description

Содержание Turbocor TT-300





































































Результаты поиска

Содержание Turbocor TT-300

Отзывы:

Похожие инструкции для Turbocor TT-300

Бренды по названию

Популярные бренды

Danfoss Turbocor TT-300, Руководство пользователя

Результаты поиска

Содержание Turbocor TT-300

Отзывы:

Похожие инструкции для Turbocor TT-300

Бренды по названию

Популярные бренды