Danfoss Turbocor TT-300 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 68

background image

Service Monitor User Manual

Danfoss Turbocor Compressors Inc.

41

ECD-00007M Rev. 1

6.9.2 Compressor Controller Alarms

Select the “CC Alarm Limits” tab to view the compressor
general alarm limits. Table 16 describes the general alarm
limits.

The limits represent the maximum temperature and/or
pressure values the compressor will tolerate before
activating an alarm.

Once an alarm is activated, the compressor motor will slow
down, and the alarm will be reported in the “Compressor
Controller” window as well as in the “Event Log” window.

An authorized user may change the temperature and/or
pressure limits to adapt to the application needs. Note
however, that the “Inverter Temperature” and the “SCR
Temperature” alarm limits cannot be altered, as changing
these limits may cause the compressor to malfunction.

Control Mode

Displays the sensor that the chiller control will try to maintain the value
of. The options are:

• Leaving Chiller Water:

Controls the water or air temperature leaving the chiller.

• Entering Chiller Water:

Controls water or air temperature entering the chiller.

• Evaporating Temperature:

Controls the evaporating (saturated suction) temperature.

Chiller Control Set Point

Value at which the controlled variable (selected through “Control
Mode”) shall be maintained.

Chiller Enable Status

Checked: chiller able to run
Unchecked: chiller will not run

Proportional Gain

Control loop - Proportional gain, 0 to 100%.

Integral Gain

Control loop - Integral gain or reset, 0 to 100%.

Startup Parameters:

Refer to 6.3 "Compressor Control" on page 23 for further details.

Suction Press Start Limit (% Trip)

Temporary alarm and trip limit for the suction pressure. The limit is set
up as a percentage of the current suction pressure limit, e.g. if a
suction pressure trip of 270 kPa was set and the suction pressure start
limit was set to 50% the temporary suction pressure, trip limit would be
135 kPa. This temporary alarm is only active while the Suction press
start fault delay is timing down.

Suction Press Start Fault Delay

Time in seconds that the temporary suction pressure alarm / fault limit
should be enabled.

Run Status Contact Close RPM

Speed at which the “Run” contact on Chiller Interface module closes.

Inlet Guide Vane Start Steps

Number of Inlet Guide Vane steps at compressor startup.

Power Control Loop Speed

PID loop gain for control of motor power.

Table 15 EEPROM Settings - Compressor Controller Parameters (Continued)

Parameter

Description

«
...
42
43
44
45
46
...
»

Содержание Turbocor TT-300





































































Отзывы:

Нет отзывов

Похожие инструкции для Turbocor TT-300

Бренд: Campbell Hausfeld Страницы: 24

Бренд: York Страницы: 4

Бренд: Sullair Страницы: 98

Бренд: Panasonic Страницы: 2

Бренд: North Star Страницы: 35

Бренд: Panther Страницы: 40

Бренд: SereneLife Страницы: 5

portable air compressor

Бренд: Polair Systems Страницы: 15

Бренд: WilTec Страницы: 12

SFX-09 Double Back

Бренд: Duncan Страницы: 2

Бренд: Wagan Страницы: 8

Бренд: Sparmax Страницы: 32

Бренд: STREET WISE Страницы: 2

Бренд: NATI Страницы: 23

PRO B6000/500 FT7.5 15B YD

Бренд: ABAC Страницы: 100

Бренд: Eastwood Страницы: 12

Бренд: AC Tool Supply Страницы: 20

AUTO SENTRY EAU99G

Бренд: Gardner Denver Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды