Danfoss BW10 020-090 Скачать руководство пользователя страница 33

33

The evaporators and condensers are single-circuit for all units.

The water connections between the heat exchangers and the 

piping of the hydronic modules have quick-connect Victaulic 

couplings to facilitate pump disassembly, if required.

A drain with a 1/4 turn valve is included in the leaving water of 

all heat exchangers.

The evaporators have 19 mm thick polyurethane foam thermal 

insulation. For option 86 (condenser insulation), the condensers 

also have 19 mm thick polyurethane foam thermal insulation.

The products that may be added for thermal insulation of the 

containers during the water piping connection procedure must 

be chemically neutral in relation to the materials and coatings 

to which they are applied.

NOTES: Monitoring during operation, re-qualification, 

re-testing and re-testing dispensation:

• 

Follow the regulations on monitoring pressurised 

equipment.

• 

It is normally required that the user or operator sets up 

and maintains a monitoring and maintenance file.

• 

If there are no regulations or to complement them follow 

the control programmes of EN 378.

• 

If they exist follow local professional recommenda-tions.

• 

Regularly inspect the condition of the coating (paint) to 

detect blistering resulting from corrosion. To do this, 

check a non-insulated section of the container or the 

rust formation at the insulation joints.

• 

Regularly check for possible presence of impurities (e.g. 

silicon grains) in the heat exchange fluids. These 

impurities maybe the cause of the wear or corrosion by 

puncture.

• 

Filter the heat exchange fluid check and carry out 

internal inspections as described in EN 378-2, annex C.

• 

In case of re-testing take the possible maximum pressure 

difference of 25 bar into consideration.

• 

The reports of periodical checks by the user or operator 

must be included in the supervision and maintenance 

file.

Repair

Any repair or modification of the plate heat exchangers is 

forbidden.

Only the replacement of the complete heat exchanger by an 

original heat exchanger supplied by the manufacturer is 

permitted. The replacement must be carried out by a qualified 

technician.

•   The heat exchanger replacement must be shown on the 

monitoring and maintenance file.

Recycling

The plate heat exchanger is 100% recyclable. After use it 

contains refrigerant vapours and oil residue.

Operating life

This unit is designed for:

• 

prolonged storage of 15 years under nitrogen charge with 

a temperature difference of 20 K per day.

• 

900000 cycles (start-ups) with a maximum difference of 6 

K between two neighbouring points in the container, based 

on 12 start-ups per hour over 15 years at a usage rate of 

57%.

12.4 - Electronic expansion valve (EXV)

The EXV is equipped with a stepper motor (2625 + 160 /- 0 

steps) that is controlled via the EXV board.

12.5 - Refrigerant

BW10 units operate exclusively with R-410A. 

12.6 - High-pressure switch and high-pressure sensor

BW10 units are equipped with an automatically reset safety 

pressure switch on the liquid line. Refer to the controls manual 

for the alarm acknowledgements.

It is strictly forbidden to modify the unit refrigerant circuit. The 

pressure switch is specific to the BW10 units - do not 

interchange it with other units. The pressure switch tap does not 

include a Schrader valve.

High-pressure switch

High-pressure sensor

The high-pressure sensor is however equipped with a Schrader 

valve. It is specific to these units and must not be replaced with 

one from other  Danfoss units.

12.7 - High and low-pressure side safety valves

The units are equipped with safety valves in accordance with 

the European directive 97/23/CE. These safety valves are 

calibrated and sized in accordance with the original high and 

low-pressure side equipment.

12.8 - Moisture indicator

Located in the liquid line, permits control of the unit charge, as 

well as the presence of moisture in the circuit. Bubbles in the 

sight glass indicate an insufficiant charge or the presence of 

non-condensibles. If moisture is present, the colour of the 

indicator paper in the sight glass changes.

Содержание BW10 020-090











































Отзывы: