Dakota Digital RET Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 25

background image

MAN#650258

7. Use the (6) Phillips screws provided to retain
the display panel.

8. Set the new lens face down and use the lines etched in the back of the lens to line up the indicator light
panels. Use tape to position them before applying a light bead of silicone around the edge to secure them.

9. Place the lens on the instrument cluster in place of the original separator plate and re-assemble the
cluster.

10. The stock indicators can be used for everything but the high beam and turn signals. See main
instruction manual for remainder of installation.

A

new wire for the oil pressure sending unit must be used.

The stock oil pressure sender wire has a resistor inline and will cause the gauge to read incorrectly if used.

The stock water temp wire can be spliced into and used but the connector will need to be removed.

4510 W. 61ST St. N.,Sioux Falls, SD 57107

Phone: (605) 332-6513 FAX: (605) 339-4106

©Copyright 2009 Dakota Digital Inc.

«
1
2
3
4
...
»

Содержание RET


























Отзывы:

Нет отзывов

Похожие инструкции для RET

Бренд: Lab.gruppen Страницы: 2

Бренд: Hunter Страницы: 2

Бренд: Tektronix Страницы: 112

Бренд: Sartorius Страницы: 165

Бренд: Casambi Страницы: 4

Бренд: Powtran Страницы: 36

Бренд: KROHNE Страницы: 88

Бренд: VAT Страницы: 149

Бренд: u-blox Страницы: 47

Бренд: RCF Страницы: 24

Бренд: wattstopper Страницы: 4

Бренд: ICP DAS USA Страницы: 8

PowerSeries Neo HS2LCDWF

Бренд: DSC Страницы: 32

GA Industries FIGURE 939

Бренд: Vag Страницы: 6

Бренд: M-system Страницы: 2

GEMINI GEMC-128

Бренд: NAPCO Страницы: 72

Бренд: D+H Страницы: 4

Бренд: Cloud Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды