Dakota Digital RET Скачать руководство пользователя страница 24

Страница: 24 / 25

650066

Symptom

Possible Problem

Solution

-----------------------------------------------------------------------------------------------------------------------------------
The gear shift indicator

The optional gear shift sending

Connect the sending unit to the

does not light up.

unit is not connected to the

control box using the

control box.

instructions supplied with the

sending unit.

The gear shift indicator

The gear shift decoder

Check the connections to the

does not operate

is not connected properly.

transmission linkage and to

properly.

the control box.

Check gear shift decoder

Installation manual.

The internal turn signal

The control box is not connected

Check the wires connected to the

and high beam

to the vehicle's electrical

HIGH, LEFT, and RIGHT

indicators do not light up.

system properly.

terminals on the control box.

The check engine

The control box is not connected

This feature is designed to work

indicator does not

to a TPI control module.

with engine control systems that

operate properly.

provide an active low signal.

The check engine

The Engine Control Module

Connect a light or similar load

indicator stays on

(ECM) needs to see the

to the ECM along with the

all of the time.

load of a light connected to it.

control box.

The Function switches

The push-button switches are

Momentary push-button or toggle

do not operate

not connected to the control

switches must be connected to

properly.

box.

the SW1 and SW2 terminals

as described in the manual.

The wrong type of switch is

The switch terminal connected

being used.

to the control box should

normally be open. When the

the switch is activated, the

terminal should make contact

to ground.

The display system starts

Sw 2 terminal is constantly

Disconnect or replace the

up in the demonstration

connected to ground.

SW2 switch.

mode and remains in it.

Содержание RET


























Результаты поиска

Содержание RET

Отзывы:

Похожие инструкции для RET

Бренды по названию

Популярные бренды

Dakota Digital RET, Инструкция по установке и эксплуатации

Результаты поиска

Содержание RET

Отзывы:

Похожие инструкции для RET

Бренды по названию

Популярные бренды