background image

 

 

              650066 

 

Thank you for purchasing the Vacuum Fluorescent Digital Dashboard from DAKOTA 

DIGITAL, the leader in custom automotive electronics.  Representing the latest electronics 
dashboard technology for the street rodder, car, and truck enthusiast alike, the digital 
instrumentation uses state of the art vacuum fluorescent display technology to give the driver up 
to date and accurate information on the operation of his or her vehicle.  As used in several 
production automobiles, vacuum fluorescent displays give superior performance and visual 
appeal over LCD or LED display systems.  Emitting a blue/green light that can be filtered to a 
wide variety of colors, the VFD system boasts excellent daytime visibility and while under 
computer control, automatically dims for nighttime driving.  Using microprocessor technology, 
the digital dashboard gives the driver additional features and benefits not typically found on any 
other brand or type of instrumentation.  Digital accuracy and solid state reliability will give you, 
the driver, quality service for miles down the road. 
 
TYPICAL DISPLAY SETUPS 

 

Содержание RET


























Отзывы: